 |
October 2005: QUIK-SET Automatic Positioning Systems
Dienes' QUIK-SET positioning system maximizes time savings by moving all knife holders simultaneously, with the benefit of high accuracy placement via computer control.
View Product Listing |
 |
August 2004: Dienes Chord Gauge
The Dienes Chord Gauge provides a quick, simple method for operators to set the proper Overlap depth of a male top knife, to the female bottom knife.
View Product Listing |
 |
March 2004: 12,000 FPM Slitting
Dienes has designed and developed a 12,000 fpm knife holder.
View Product Listing |
 |
February 2004: DF Holder Handle & Dust Cover
View Product Listing |
 |
January 2004: Quik-Link Manual Positioning
Quik-Link is available with monitor digital readout from magnetostrictive accuracy location sensing devices.
View Product Listing |
 |
December 2003: New ES-Tab
Pivot design replaces sliding design;
stiffer, more rigid mount.
View Product Listing |
 |
November 2003: Center Linear Bearing System
Dienes’ answer to the inaccuracies and frustrations caused by dovetail mounting arrangements is the “CLB System” (Center Linear Bearing). Excessive knife side loading and subsequent reduced knife life from misuse of dovetail rack and pinion arrangements are eliminated.
View Product Listing |
 |
October 2003: Dienes Knife Blade Regrinder
Dienes has developed a fully automatic, programmable knife blade grinder that is fast, angle
accurate and provides consistent < 10 rms finishes. Super finish below 1 rms is available.
Optional tooling measures each blade before mounting and automatically sets the grinder
operation to the blade dimensions read.
View Product Listing |
 |
September 2003: Dienes Edge Trim System
Dienes Edge Trim Systems can be provided with manual, semi or fully automatic
configurations. Any Dienes shear knife holder can be utilized for a wide variety of materials.
The single frame construction assures the once set, the top and bottom knife relative
locations are maintained during position changes.
View Product Listing |
 |
August 2003: Dienes Model PSG-50 rotary knife holder
The Dienes Model PSG-50 rotary knife holder can be adapted to hold three indexing
razor blades in a 360 degree guard. When pneumatically retracted from the web, the
guard springs into place to cover the blades.
View Product Listing |
| |
 |
July 2003: Less than 2" Wide Motor Driven Bottom Knife
The Dienes E-TORQ motor driven bottom knife offers full torque from 5 fpm to 10,000 fpm with a 1.89” slit width capability. The “brushless” servo-motors are totally enclosed, sealed to slitting dust and have separate servo drives.
View Product Listing |
| |
 |
May, 2003: Heated Shear Knife Slitting
Utilizing controlled airflow and a quartz heater the top knife temperature can be accurately controlled with near instant heat dissipation.
View Product Listing |
| |
 |
April, 2003: Light Guided Knife Set Up
A built-in sensor finds the bottom knife edge and tells the operator through a series of lights when the top knife blade is properly located to the bottom.
View Product Listing |
| |
 |
January, 2003: Slitting Adhesive Materials
Special teflon based coatings can be added to Dienes knife blades that extend run time on those adhesive slitting applications that have frequent down time for cleaning.
View Product Listing |
| |
 |
December, 2002: Dienes Micro Width Slitting
Dienes Micro Slitters easily handle narrow slit width soft materials. Slit widths below 0.060" are possible.
View Product Listing |
| |
 |
November, 2002: Rigid Material Slitting
Dienes Quill Set Slitters easily handle those narrow web stiff materials that standard knife holders are no match for.
View Product Listing |
| |
 |
October, 2002: 50mm Wide Knife Motor
The Model E-50 DC motor provides the narrowest slit width possible for individually driven shear slitting bottom knives.
View Product Listing |
| |
 |
September, 2002: Constant Knife Side Load Force
The DF-150-200 is the only shear knife holder that removes the mechanical return spring from effecting knife side load force and knife life.
View Product Listing |
| |
 |
August, 2002: Center Linear Bearing (CLB) System
Dienes' answer to the inaccuracies and frustrations caused by dovetail mounting arrangements is the CLB System (Center Linear Bearing). Excessive side loading, top knife jumps, and subsequent reduced knife life and holder failure from misuse of dovetail rack and pinion arrangements are eliminated.
View Product Listing |
